Soulsby Synths Forum

Technical Support => Atmegatron/Odytron Hardware technical support => Topic started by: gr33n on December 02, 2019, 02:16:31 PM

Title: Atemgatron (Odytron Ed) not powering up
Post by: gr33n on December 02, 2019, 02:16:31 PM
I have the Atmegatron Odytron SE that suddenly won't power up. I was uploading some different software and then it seemed to lose power/lights out.

I had successfully re-installed the Odytron v1.3 software. I think I have accidentally uploaded the Odytron patches (Ody Factory.eep.hex) as software rather than via the 'load patches' option(!) - could this have messed things up?

I haven't had any problems before and am using the supplied cable, etc. but it's been a while since I uploaded different software so am worried that I might have not followed the proper procedure. Any ideas would be gratefully received! Thank you.
Title: Re: Atemgatron (Odytron Ed) not powering up
Post by: paulsoulsby on December 06, 2019, 10:44:34 AM
Hi - the Odytron Patches should be a .eep file, not .hex, so you shouldn't have been able to load this as firmware (it'll only upload .hex files, not .eep)

What happens if you upload a different firmware?  Does the software upload OK and all is back to normal? If it doesn't upload, click the "show console" box in Easy Uploader and copy and paste the text here, so I can see what happens.  thanks
Title: Re: Atemgatron (Odytron Ed) not powering up
Post by: gr33n on December 06, 2019, 06:01:52 PM
Many thanks for getting back to me. Unfortunately, it isn't powering up at so I haven't been able to upload anything so I'm not sure where to go from here:

"/Applications/EasyUploader.app/Contents/MacOS//avrdude" -c arduino -p m328p -C "/Applications/EasyUploader.app/Contents/MacOS/avrdude.conf" -P /dev/cu.Bluetooth-Incoming-Port -U flash:w:"/Volumes/HD 2 Music/x Atmegatron/AtmegatronV2-5.hex":i
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00

avrdude done.  Thank you.
Title: Re: Atemgatron (Odytron Ed) not powering up
Post by: paulsoulsby on January 06, 2020, 10:00:49 PM
Hi - I think you haven't installed the FTDI cable. You need to download and install the drivers.  Then select it in the dropdown box in Easy Uploader. You've currently got the Mac's Bluetooth port selected.
Title: Re: Atemgatron (Odytron Ed) not powering up
Post by: gr33n on April 06, 2020, 10:02:27 PM
Doh, sorry!! That got it all sorted. Thanks a lot for your help, Paul.