Hi!
I recently bought the Atmegatron but haven't been able to upload any new software. I checked the other posts about it, but still couldn't figure out what's wrong (ie I checked that the cable is correctly inserted, I've flipped the programmer/midi switch to the left etc..). So far I've tried the Delayertron, the Odytron and the Atmegadrum software but no luck.
This is the cable I am using:
https://www.elfa.se/en/usb-cable-assembly-usb-ttl-cmos-ftdi-ttl-232r-5v/p/17320673?queryFromSuggest=true
With the VCP drivers from here:
http://www.ftdichip.com/Drivers/VCP.htm
This is the error messages I keep getting:
Arduino: 1.6.5 (Windows 7), Board: "Arduino/Genuino Uno"
Sketch uses 25,400 bytes (78%) of program storage space. Maximum is 32,256 bytes.
Global variables use 1,943 bytes (94%) of dynamic memory, leaving 105 bytes for local variables. Maximum is 2,048 bytes.
Low memory available, stability problems may occur.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xd2
Problem uploading to board. See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xd2
Any ideas?
Regards,
Johan
I recently bought the Atmegatron but haven't been able to upload any new software. I checked the other posts about it, but still couldn't figure out what's wrong (ie I checked that the cable is correctly inserted, I've flipped the programmer/midi switch to the left etc..). So far I've tried the Delayertron, the Odytron and the Atmegadrum software but no luck.
This is the cable I am using:
https://www.elfa.se/en/usb-cable-assembly-usb-ttl-cmos-ftdi-ttl-232r-5v/p/17320673?queryFromSuggest=true
With the VCP drivers from here:
http://www.ftdichip.com/Drivers/VCP.htm
This is the error messages I keep getting:
Arduino: 1.6.5 (Windows 7), Board: "Arduino/Genuino Uno"
Sketch uses 25,400 bytes (78%) of program storage space. Maximum is 32,256 bytes.
Global variables use 1,943 bytes (94%) of dynamic memory, leaving 105 bytes for local variables. Maximum is 2,048 bytes.
Low memory available, stability problems may occur.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xd2
Problem uploading to board. See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xd2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xd2
Any ideas?
Regards,
Johan